How Do You Charge Beats Wireless Headphones

The Beats wireless headphones have a built-in rechargeable lithium-ion battery that powers the ANC and provides up to 20 hours of playback. To charge your Beats wireless headphones read on:

How to Charge Your Beats Wireless Headphones

  • Connect the charging cable to the micro USB port on the right headset.
  • Connect the USB end of the cable to a power source.

It takes approximately 2 hours to fully charge an empty battery using the power adapter. It may take longer if you are charging via USB from your laptop or another device.

How do you charge beats wireless headphones

Battery Status While the Beats Wireless Headphones Are Charging

The blinking LEDs on the meter mean the following:

When disconnected from the power source:

  • 5 white lights indicate full or almost full charge.
  • 1 steady red light indicates a low charge.
  • 1 flashing red light indicates that the battery is almost empty.
  • No light indicates the headset is turned off or the battery is not charging

When connected to a power source:

  • 5 white lights indicate the maximum load.
  • 1 blinking white light indicates that the battery is almost empty.

Tips on How to Fix your Beats Wireless Headphones if it Stopped Charging

Are your Beats wireless headphones not charging? Then you are exactly right here

Try a Different Power Source

The power source, or what most people would call an “adapter”, comes in many shapes and forms. Everyone has specifications that define how much power they can deliver to a connected device. You can learn more about the performance of an adapter on the back of the adapter.

If you connect a charger with lower power than your headphones need, the low power can significantly slow down or even stop the charging process.

Try charging your headphones from a different power source that matches the output power your headphones need. Make sure you give them plenty of time as the battery may be completely discharged and it will take longer to charge than usual. If your Beats headphones charge after plugging them into the new adapter, the problem is with your adapter.

Reset Your Device

Beats, in their official online guide, recommends that customers reset their headphones in case they experience problems with Bluetooth connectivity or charging.

  • First, make sure your device is not connected to cables.
  • Next, find and hold the power button for about 10 seconds, then release it.

You will see your device’s LED indicators flash three times, this also indicates that your beats wireless headphone has been reset

The above solution only works with “Solo2 Wireless”. If you have a different pair, check out the official Beats guide on how to reset your specific device type.

Try a Different Cable

Charging cables are known to break easily. A seamless tug can break thin cables. This breakage can prevent power from being properly delivered from the power source to your device, preventing your Beats headphones from charging.

You can tell if this is causing your problems by trying another cable that you know will work fine. Make sure you give your device enough time to charge.

Clean Your Charging Case

If your specific headset model comes with a charging case or stand, debris accumulated in the charging ports on the stand can cause problems when charging the headset. Your case is connected to your device via two connectors located where you put your headphones on the case.

Users have raised this issue, and Beats admits that sometimes dirt builds up around the ports and prevents their product from charging.

First, examine your case, as well as your headphones, and make sure there is no dirt around the connectors. You can properly clean the area with a cotton swab or brush. This will fix the bad connection and hopefully eliminate the problem!

Replace the Batteries

Your device probably has a lithium-ion battery, which is used by almost all manufacturers due to its high energy density. This means that a very small battery can hold a lot of charges.

Most of these batteries have a limited number of charge cycles. This means that you can only charge and then discharge your device a limited number of times and over time your battery’s ability to maintain a full charge will decrease.

If your headset is an old pair, a burned battery could be the cause of a charging problem. In that case, you can look for battery replacements for your specific headphones. You can find replacement batteries for your device on sites like eBay, or you can contact a local repair shop to see if they have what you need.

Broken Port

This solution is for those who are familiar with electronics and are familiar with soldering components onto a circuit board. If none of the above fixes worked for you, here’s one more thing that could fix your problem.

Your device uses a connector to carry electrical power from the power adapter to the circuitry inside your device. Over time and with regular use, these ports can wear out or even break, resulting in a poor connection.

This is often why the electronics have no power problem and replacing this port can fix it. You can easily find spare parts for your specific device on websites such as Amazon or eBay.

Hope you were able to solve your problem, or at least find out what was causing your Beats headphones charging problem. If not, you can check if your device is still under warranty and if you can get a replacement by contacting Beat customer support. I hope this fixes the problem with charging your Beats wireless headphones.

One of the most common and annoying problems most headphones develop over time is they stop charging. Beats, co-founder of the infamous rapper Dr. Dre is by far one of the most renowned headphone manufacturers in the world. But even his headphones are not immune to this free charge problem.

Also Read: How Do I Charge My JBL Flip 3

Leave a Reply

Your email address will not be published. Required fields are marked *

Back to top button